Skip to content

How to Price RV Repair Jobs: Labor Times, Parts and Fees

How to price RV repair jobs: flat rate vs actual hours, labor time guides, diagnosis, parts markup and matrices, fees, sublets and packaged jobs.

Estimates and pricing10 min read
A service counter in an RV repair shop where jobs are quoted
On this page
  1. Flat rate or actual hours
  2. Where labor times come from
  3. Price diagnosis as its own line
  4. Parts: cost, markup and the matrix
  5. Shop supplies, fees and disclosure
  6. Sublet work
  7. Packaged jobs for the work you quote every week
  8. Give the customer job-by-job choices
  9. Keeping prices the same no matter who quotes
  10. Pricing jobs in RVDesk
  11. Common questions
  12. Sources

A posted labor rate is only half of a price. The other half is everything a service writer decides at the desk: how many hours to put on the job, what to charge for the parts, whether diagnosis is its own line, what the outside upholstery shop’s bill becomes on your invoice, and which fees show up. Two writers in the same shop can make those calls differently and quote the same roof reseal a long way apart.

This guide is about pricing the job, not setting the rate. If you haven’t worked out your hourly rate from your own costs yet, start with how to set RV repair labor rates. Once the price is built, our guide to writing RV repair estimates customers approve covers how to present it and get a yes.

Flat rate or actual hoursLink to the section “Flat rate or actual hours”

Every labor line is sold one of two ways. With a flat rate, you quote a set number of hours for the job and charge that number whether the tech finishes early or runs long. With actual time, you quote an estimate and bill the hours the work really took, usually with a ceiling the customer has agreed to.

How the two approaches move risk
QuestionFlat rateActual hours
Customer knows the labor priceBefore the work startsAfter it’s done, within the estimate
Job runs longThe shop absorbs itThe customer pays, if they approved it
Job runs shortThe shop keeps the differenceThe customer pays less
Works best forRepeatable jobs you’ve done many timesDiagnosis, water damage, anything you can’t see yet

Most RV shops end up using both. A bearing repack on a tandem-axle trailer is the same job every time and suits a flat price. Chasing a leak behind a wall panel isn’t, and a fixed price there is a guess. Whichever you use, put it on the line so the customer knows whether the number can move.

Where labor times come fromLink to the section “Where labor times come from”

RV service has published time guides, though nothing as universal as the guides on the car side. The RV Dealers Association’s education foundation has published a Service Management Guide that a 2002 announcement described as “developed by dealers, service managers and technicians” to provide average work unit times, and as a tool to measure productivity in the service department. A later announcement described a 12th edition with more than 100 pages of average work unit times, sold through the Mike Molino RV Learning Center.

Manufacturer warranty schedules are a different thing. Winnebago describes dealers doing warranty repairs billing the manufacturer for their labor time based on a pre-agreed pricing schedule. That schedule is what one manufacturer has agreed to pay you on its own warranty claims. It is not a retail price, and copying warranty hours onto customer-pay work means pricing your labor to someone else’s contract.

The guide that fits your shop best is your own history. If techs clock time against each job, a few months of records show what a slide topper replacement or a water pump swap actually takes in your bays, with your equipment. Use a published guide as a starting point and a sanity check, then adjust to what you measure.

Price diagnosis as its own lineLink to the section “Price diagnosis as its own line”

Diagnosis is labor, and it is the labor most often given away. When it is folded into the repair, a customer who declines the repair has paid nothing for the hour your tech spent finding the problem. Quote it as its own line, with its own hours or a fixed diagnostic charge, and get it approved before the teardown.

Some states expect this. California’s invoice regulation requires services and repairs to be listed with the price for each, “including any diagnosis or warranty repairs.” Decide in advance what a diagnostic charge buys: a set block of time, and what happens when the problem needs more than that. Write it down so every writer says the same thing at the counter.

Parts: cost, markup and the matrixLink to the section “Parts: cost, markup and the matrix”

Parts pricing starts with what the part cost you, landed: the invoice price plus freight if you paid it. From there, a shop needs a written rule for the selling price. Without one, each writer prices from memory or from the supplier’s list price, and margin drifts.

The simplest rule is one markup on everything. The trouble is that one percentage behaves very differently at each end of the price range. The same markup that is reasonable on a $400 water heater can leave almost nothing on a $3 fitting once you count the time to order, receive, shelve and bill it. A parts matrix fixes that by setting the markup by cost range: higher on inexpensive parts, lower as cost goes up.

Ratchet+Wrench described this in a 2015 article on building a parts matrix, calling it “a spreadsheet that sets mark-up amounts for parts of different prices.” The shop owners it profiled used multipliers that fell as part cost rose, aimed at an overall gross profit goal, and the article warned against basing a pricing structure on competitors. Those figures came from automotive shops and are one example, not an RV standard. Build your own ranges from the margin your shop needs.

Whatever the method, be clear which number you are setting. A multiplier, a markup and a gross profit percentage describe the same price in different terms, and mixing them up costs money:

Gross profit % = 1 − (1 ÷ multiplier). A 2.0 multiplier is a 100% markup and a 50% gross profit. A 1.5 multiplier is a 50% markup and about a 33.3% gross profit.

A matrix example (made-up numbers)Link to the section “A matrix example (made-up numbers)”

The ranges below are invented to show the arithmetic. They are not an industry figure and not a recommendation.

Illustrative parts matrix
Part costMultiplierGross profitExample
Up to $252.050%$12.00 cost → $24.00
$25.01 to $1001.637.5%$60.00 cost → $96.00
Over $1001.35about 25.9%$400.00 cost → $540.00

Review the ranges when supplier costs move, and keep the cost on every part current. A matrix only works on the cost you feed it. If a part was received at a higher price and nobody updated it, the matrix prices from the old cost.

Shop supplies, fees and disclosureLink to the section “Shop supplies, fees and disclosure”

Rags, sealant tubes you open and partly use, cleaners and the like are a real cost. Shops recover them in different ways: built into the labor rate, charged as specific items, or as a named fee. Whichever you choose, the customer should see it on the estimate, not first on the invoice.

Check your state before you add a percentage-based supplies fee. California’s invoice regulation says separate billing “for items generically noted as shop supplies, miscellaneous parts” and the like is prohibited. The state’s Bureau of Automotive Repair explained in its Fall 2024 newsletter that repair dealers may not charge general fees to cover their costs, and may not charge a general hazardous waste fee to every customer; a waste charge has to relate to the specific customer’s vehicle. Whether those rules reach your RV work depends on the vehicle and the work, so confirm with the Bureau if you operate there.

At the federal level, the FTC’s Rule on Unfair or Deceptive Fees took effect May 12, 2025 and covers live-event tickets and short-term lodging, not repair shops. That doesn’t make hidden fees a good idea. A fee the customer didn’t expect is the line they argue about at pickup.

Sublet workLink to the section “Sublet work”

Some jobs leave the building: windshield replacement, chassis alignment, upholstery, a frame weld. The outside vendor’s bill becomes a line on your invoice, and you need a policy for what you charge on it. Shops commonly pass it through at cost or add a handling charge for arranging, transporting and standing behind the work. Decide which, and apply it the same way every time.

  • Get the vendor’s quote before you quote the customer, and put it on the estimate as its own line.
  • Record the vendor’s cost and your selling price separately, so you can see what the sublet earned.
  • Say who warrants the work: you, the vendor, or both.
  • Include any time your own tech spends removing, reinstalling or transporting the unit as labor on the job.

Packaged jobs for the work you quote every weekLink to the section “Packaged jobs for the work you quote every week”

Most RV shops quote the same handful of jobs over and over: winterizing and dewinterizing, a roof inspection and reseal, wheel bearing service, a slide seal, a water heater anode and flush. Each of those is a good candidate for a saved, priced package, often called a canned job, with the labor, the parts and any fees already on it.

A package is only as good as its contents. Write down exactly what is included, so the customer and the writer both know where the job ends:

  • Winterizing: whether it covers draining and blowing out lines or filling with antifreeze, how much antifreeze is included, and whether the water heater is bypassed. Our winterization service checklist has the full list.
  • Roof reseal: inspection, cleaning, how many lineal feet or which fixtures are included, and how damage found underneath is handled. See the roof inspection and resealing guide.
  • Bearing repack: priced per axle, with seals included. Axle maker Dexter says bearings should be lubricated every 12 months or 12,000 miles, which makes this a job worth a standing price and a reminder.

Packages are also where flat rate makes the most sense. You’ve done the job enough times to know the hours, so a fixed price is fair to both sides.

Give the customer job-by-job choicesLink to the section “Give the customer job-by-job choices”

Price each concern as its own job with its own subtotal, so the customer can approve some and wait on others. Where there is a real choice, price both options: reseal the roof now or replace the membrane, rebuild the slide mechanism or replace the motor. Two honest prices let the owner decide, and the declined option is on record if the question comes back next season. Presenting and recording those choices is covered in the estimates guide linked above.

Keeping prices the same no matter who quotesLink to the section “Keeping prices the same no matter who quotes”

A customer who hears two prices for the same job from two people stops trusting both. Consistency comes from writing the rules down and putting them where writers work:

  • One labor rate, or a short list of rates with a written rule for when each applies.
  • Standard hours for common jobs, kept in saved packages rather than in people’s heads.
  • A parts pricing rule the system applies from cost, with a reason recorded when someone overrides it.
  • A written diagnostic policy: what it costs and what it covers.
  • Named fees and a sublet policy, applied the same way on every estimate.
  • A monthly look at sold hours against clocked hours, by job type, to catch packages priced too low.

Pricing jobs in RVDeskLink to the section “Pricing jobs in RVDesk”

In RVDesk, the estimate is built from the same jobs, parts and labor that end up on the invoice. Canned jobs save the work you quote often, with labor and parts, so it can be dropped onto any estimate. Pricing matrices are set up in settings: ranges by part cost, each set as a multiplier, markup or gross profit percentage, and a part line with the matrix applied prices from its cost. Labor matrices work the same way on hours.

Parts keep cost and price separately, so job profit uses what the part really cost. Sublets are recorded on the work order with their cost and price, and each job shows hours done against hours sold.

Common questionsLink to the section “Common questions”

Should an RV shop charge flat rate or actual hours?

Many shops use both: flat rate for repeatable jobs like bearing repacks and winterizing, and actual time with an approved estimate for diagnosis and work where the damage can’t be seen yet. Say on each line which one it is.

Is there a labor time guide for RV repair?

The RV Dealers Association’s education foundation has published a Service Management Guide of average work unit times. Manufacturers also set warranty labor schedules, but those govern what they pay on their own claims. Your own clocked time is the best guide for customer-pay work.

What is a parts pricing matrix?

A table that sets the markup on a part by its cost range, usually higher on inexpensive parts and lower on expensive ones, so the selling price comes from a written rule instead of each writer’s judgment.

Can I charge a shop supplies fee on RV repairs?

It depends on your state. California prohibits separate invoice lines for items generically noted as shop supplies or miscellaneous parts. Wherever you are, name any fee on the estimate before the customer approves.

Want to see a canned job and a parts matrix price an RV estimate? Book a demo and we’ll walk through RVDesk with your shop’s common jobs.

Sources

  1. F&I and Showroom: RVDA Education Foundation Service Management Guide includes time changes and additions (March 19, 2002) (fi-magazine.com)
  2. Naylor Network: New Edition of Service Management Guide Now Available Through Mike Molino RV Learning Center (naylornetwork.com)
  3. Winnebago: RV Consumer: Warranties and Dealers (winnebago.com)
  4. Ratchet+Wrench: Building a Parts Matrix (November 1, 2015) (ratchetandwrench.com)
  5. California Code of Regulations, Title 16, § 3356 (invoice requirements) (law.cornell.edu)
  6. California Bureau of Automotive Repair: Repair transaction fees (Automotive Repair and Smog Check News, Fall 2024) (bar.ca.gov)
  7. Federal Trade Commission: Rule on Unfair or Deceptive Fees, Frequently Asked Questions (ftc.gov)
  8. Dexter: Frequently Asked Questions, Bearings (dextergroup.com)

Written by the RVDesk team

We build RVDesk alongside a mobile RV repair business in Redding, California.

See RVDesk on your shop’s work.

Mon–Fri, 8 AM–5 PM Pacific