Skip to content

RV De-Winterizing Checklist: A Spring Service Guide for RV Shops

An RV de-winterizing checklist for shops: flush antifreeze, sanitize the fresh water, fill the water heater before power, then check propane, tires and roof.

RV maintenance10 min read
Technicians working on a Class A motorhome inside an RV shop bay
On this page
  1. Start with the fall work order
  2. Step 1: Flush the antifreeze and put the plumbing back
  3. Step 2: Sanitize the fresh water system
  4. Step 3: Fill the water heater before you power it
  5. Step 4: Pressure the system and look for leaks
  6. Step 5: Appliances, toilet and macerator
  7. Step 6: Propane leak check and gas appliances
  8. Step 7: Batteries and safety alarms
  9. Step 8: Tires, wheels and brakes
  10. Step 9: Roof, sealants and slide-outs
  11. The de-winterizing checklist
  12. Book it and document it as a spring service
  13. Common questions
  14. Sources

De-winterizing is where a shop finds out how the fall went. A split line, a heater element that burns out on the first day, a propane fitting that loosened over the winter: they all show up in spring, and the customer usually finds them at the campground if the shop doesn’t find them first in the bay.

This checklist is the spring companion to our RV winterizing checklist. The procedural details come from RV and appliance manufacturer manuals, mostly Jayco’s owner’s manuals, Dometic’s and Suburban’s water heater guidance and Splendide’s washer instructions. Plumbing layouts differ between models, so treat it as your shop’s standard and the unit’s own manual as the final word.

Start with the fall work orderLink to the section “Start with the fall work order”

A good de-winterization starts at the counter, not the water inlet. If your shop winterized the rig, the fall work order should say whether it was the antifreeze or air pressure method, how the water heater bypass was left, and what was taken out. If another shop or the owner did it, ask, and tag anything you can’t confirm for the tech to check by eye.

The items that most often get missed in spring are the ones that came out in the fall:

  • The water heater drain plug or anode. Suburban’s guidance for heaters with no bypass is to remove the anode rod and fit a 3/4-inch drain plug when antifreeze is used. That anode has to go back in.
  • The water filter cartridge. Jayco’s manual says to remove cartridge filters before winterizing with antifreeze, and in spring, after flushing the antifreeze out, to wash out the filter housing and reinstall the filter.
  • Batteries. Jayco’s storage checklist tells owners to remove all batteries and store them where they won’t freeze, so they may be in the customer’s garage, not on the rig.

Step 1: Flush the antifreeze and put the plumbing backLink to the section “Step 1: Flush the antifreeze and put the plumbing back”

Jayco’s towable manual sets out the spring steps after a winterization: turn off all faucets inside and outside, reinstall the water filter if applicable, reinstall the water heater drain plug, and close all low-point and fresh water drains. After an antifreeze winterization, the antifreeze has to be flushed out of the lines first.

  1. Leave the tank water heater in bypass for now, so antifreeze and, next, sanitizer stay out of the tank.
  2. Close the low-point drains and the fresh water tank drain, and reinstall the water heater drain plug or anode.
  3. Make sure the antifreeze siphon valve at the pump is back in its normal position.
  4. Run potable water through every fixture, hot and cold sides, including the outside shower and the toilet, until the antifreeze is out.
  5. Wash out the filter housing and reinstall the cartridge once the antifreeze is flushed, as Jayco’s manual describes.

Jayco’s manual describes the bypass valves in normal mode as having both handles pointing toward the water heater connections. That is where they end up once sanitizing is done, not before.

Step 2: Sanitize the fresh water systemLink to the section “Step 2: Sanitize the fresh water system”

Jayco recommends sanitizing the fresh water system when the RV is new, at the beginning and end of each season, and when the system becomes contaminated or every three months of use. Its manual gives two bleach strengths:

Fresh water sanitizing solutions, as Jayco’s towable owner’s manual gives them
StrengthMixAmountContact time
50 ppm1/4 cup of household bleach per gallon of waterOne gallon of solution for every 15 gallons of tank capacityAt least 4 hours
100 ppm1/2 cup of household bleach per gallon of waterOne gallon of solution for every 15 gallons of tank capacityAt least 1 hour

Jayco’s procedure, in short:

  1. Water heater off at both the electric and propane switches, and the tank heater set to bypass.
  2. Level the rig and drain the fresh water system, then close the drains and reinstall the heater drain plug.
  3. Remove the cartridge water filter, pour the solution into the fresh tank through the gravity fill, and top the tank up with potable water.
  4. Run the pump and open each hot faucet until water flows continuously and you can smell chlorine, then each cold faucet, including the outside shower and the toilet.
  5. Leave the solution in the tank and lines for the contact time, then drain it.
  6. Refill the fresh tank with potable water, heater still bypassed, and run every faucet until the chlorine smell is gone. Drain again.

After sanitizing, Jayco says to set the bypass valves to normal, close every faucet, the gravity fill and the drains, make sure the heater drain plug is in, and wash out and reinstall the water filter. If the customer complains of a chlorine taste afterward, the manual suggests flushing with one quart of vinegar to five gallons of clean water.

Step 3: Fill the water heater before you power itLink to the section “Step 3: Fill the water heater before you power it”

This is the step that costs money when it’s skipped. A drained tank water heater has to be full before either heat source comes on:

  • Dometic (Atwood) says not to operate its heaters without water in the tank, and that turning power on without water covering the heating element may burn out the element and void the warranty.
  • Suburban says operating without water on the 120-volt electric side will damage the element, and that running the gas side dry can melt the insulation jacket.
  • Jayco says to make sure the water heater is filled before use, and that opening both hot and cold faucets while filling helps remove air pockets from the heater.

With the bypass back in normal, run water into the system and open the hot faucets until water flows steadily with no air, which tells you the tank is full. Jayco’s Class C manual describes the same order on city water: the tank water heater fills first, then the lines and faucets, and only then does the water heater switch go on.

While the heater is open, look at the burner. Dometic warns that spiders, mud wasps and other insects build nests in the burner tube, causing poor combustion and delayed ignition, and its manual describes the warning signs: a burner sound that changes, or a flame that goes from hard blue to soft, lazy or very yellow. A rig that sat all winter is a likely place for a nest.

Step 4: Pressure the system and look for leaksLink to the section “Step 4: Pressure the system and look for leaks”

Jayco’s plumbing maintenance list says to check all lines and fittings for leaks before each trip or storage, and to inspect all faucets and sink connections. Spring is when that check matters most, because the rig is being pressurized for the first time since it was drained.

  • With the pump on, or on city water, listen for the pump cycling when no faucet is open.
  • Look under every sink, behind the water heater access, at the pump, at the low-point drains and at the city water inlet.
  • Check the toilet supply line and valve, the outside shower and any washer or ice maker supply.
  • Photograph anything wet. A slow drip found in the bay is a quick fix; found after the customer leaves, it becomes a floor.

Step 5: Appliances, toilet and maceratorLink to the section “Step 5: Appliances, toilet and macerator”

  • Washer-dryer. Splendide’s instructions for its front-loading washer-dryers say to flush the water pipes first, then reconnect the inlet hoses, turn the faucets on, restore power, add half a tablespoon of powder detergent and run a complete express cycle to clean out any remaining antifreeze. Newer models have their own manuals.
  • Refrigerator ice maker, dishwasher and other water appliances. Follow each appliance’s own manual, as Jayco’s manuals direct for winterizing.
  • Macerator. Jayco’s towable manual notes that emptying the black tanks in the spring flushes the antifreeze out of the macerator system.
  • Water heater pressure and temperature valve. Dometic notes that a relief valve dripping while the heater runs doesn’t mean it is defective; its tank is designed with an air gap at the top that the water absorbs over time. Dometic’s manual explains how to restore that air gap, with the heater off and the water cool.

Step 6: Propane leak check and gas appliancesLink to the section “Step 6: Propane leak check and gas appliances”

Jayco’s travel checklist says to have the propane system checked for leaks by your dealer, which makes it a natural spring service line. Jayco’s leak test guidance:

  • Apply a soapy water solution to the fittings; bubbles mean a leak.
  • Avoid solutions containing ammonia or chlorine, which Jayco says can crack metal tubing and brass fittings.
  • Never use an open flame to test for a leak.
  • If a leak is found, Jayco says to shut off the propane system right away. Repair it before the system goes back into service.

When turning the propane back on, Jayco says to close all burner valves and controls first, then open the main tank valve slowly and listen for hissing. Light each appliance according to its own manual and confirm it runs normally.

Step 7: Batteries and safety alarmsLink to the section “Step 7: Batteries and safety alarms”

Jayco’s checklist says to make sure batteries are fully charged and installed correctly before travel. If they were stored off the rig, reinstall them and check the connections; if they stayed on with the negative cable disconnected, as Jayco’s storage guidance allows, reconnect it. Note the state of charge on the work order either way.

Jayco also says to test the smoke alarm after storage, before each trip and at least once a week during use, and its checklist includes testing safety detectors. Test the smoke alarm and the carbon monoxide and propane alarm as part of the spring visit, and write down what you found.

Step 8: Tires, wheels and brakesLink to the section “Step 8: Tires, wheels and brakes”

  • Tires. Jayco’s checklist says to check tires for wear, pressure and damage, using the pressure on the rig’s Federal Certification label. Its storage checklist recommends covering tires exposed to sunlight to prevent weather checking and UV damage, so look for cracking on rigs that sat uncovered.
  • Lug nuts. Jayco’s manual lists after winter storage as one of the times to check wheel lug torque, using a calibrated torque wrench rather than an impact wrench, in two stages and in the correct star pattern. The torque values are on the label and in the manual for the specific wheel.
  • Brakes. Jayco’s checklist says to have the brakes adjusted by a qualified service technician and to test them. On a towable, that includes the connection to the tow vehicle and the lights.

Step 9: Roof, sealants and slide-outsLink to the section “Step 9: Roof, sealants and slide-outs”

Winter is hard on sealant. Jayco says road vibration, UV exposure, pollution and freezing temperatures can all damage sealants, and recommends inspecting all sealants every six months, including the roof, moldings, doors, vents and attachments, replacing sealant that shows cracks, peeling, gaps or other deterioration, with the same type of sealant as before. Jayco also warns that 8 inches or more of snow, or 2 inches or more of ice, puts excessive weight on the roof and can damage the roof and seals.

That makes the spring visit the right time for a full roof inspection; our roof inspection and resealing guide covers what to check. Run the slide-outs through a full cycle while the rig is in the bay and look at the seals; the slide-out maintenance guide covers the common failures.

The de-winterizing checklistLink to the section “The de-winterizing checklist”

Print it, or better, build it into an inspection template so every tech runs the same list:

  • Fall work order reviewed: method, bypass position, removed parts
  • Low-point and fresh tank drains closed; siphon valve at the pump set to normal
  • Water heater drain plug or anode reinstalled; anode condition noted
  • Antifreeze flushed from every fixture, hot and cold, outside shower and toilet
  • Fresh water system sanitized at the manual’s ratio and contact time, then rinsed until the chlorine smell is gone
  • Water filter housing washed out and cartridge reinstalled
  • Water heater bypass set to normal; tank filled and air purged before gas or electric is turned on
  • Burner tube checked for insect nests; heater runs on gas and electric
  • System pressurized; every fitting, faucet and supply line checked for leaks
  • Washer, ice maker and other appliances returned to service per their manuals
  • Propane system leak-checked with soapy water; each gas appliance lit and running
  • Batteries charged, installed and connected; state of charge recorded
  • Smoke, carbon monoxide and propane alarms tested
  • Tires checked for wear, pressure and cracking; lug nuts torqued; brakes adjusted and tested
  • Roof and sealants inspected; slide-outs cycled and seals checked

Book it and document it as a spring serviceLink to the section “Book it and document it as a spring service”

The easiest spring visit to get is the one booked in the fall, while the customer is standing at the counter. In RVDesk, that is an appointment on the scheduling calendar with the drop-off, the estimated pickup and the assigned tech on it, and it becomes the work order in one click when the rig arrives, with the customer and the rig already filled in. The fall work order is on the rig’s history, so the tech can see what was removed before touching a valve.

Build the checklist above into a digital inspection and techs work through it on a phone or tablet in the bay, marking each item pass, attention or fail with photos: the reinstalled anode, a weeping fitting, cracked roof sealant, a tire with weather checking. Tie an item to a canned job and a failed item goes onto the estimate in one tap, and the customer approves the work from their phone. Anything they decline stays with the rig for the next visit.

Common questionsLink to the section “Common questions”

How do you de-winterize an RV?

Flush the RV antifreeze from every fixture, reinstall anything removed in the fall (the water heater drain plug or anode, the water filter), close the drains, sanitize the fresh water system, set the water heater bypass back to normal and fill the heater before turning it on. Then check for water leaks, leak-check the propane system with soapy water, and inspect batteries, alarms, tires, brakes and the roof.

How much bleach do you use to sanitize an RV fresh water system?

Jayco’s owner’s manual gives 1/4 cup of household bleach per gallon of water for a 50 ppm solution, left for at least four hours, or 1/2 cup per gallon for 100 ppm, left for at least one hour, using one gallon of solution for every 15 gallons of tank capacity. Rinse afterward until the chlorine smell is gone. Check the manual for the specific rig.

Can you turn on an RV water heater before it is full?

No. Dometic says turning power on without water covering the heating element may burn out the element and void the warranty, and Suburban says running its heaters without water damages the electric element and can melt the insulation jacket on the gas side. Fill the tank and open the hot faucets until water flows without air first.

How do you check an RV for propane leaks?

Jayco’s manual says to apply a soapy water solution to the fittings and watch for bubbles, to avoid solutions with ammonia or chlorine because they can crack tubing and brass fittings, and never to use an open flame. Its travel checklist recommends having the propane system checked for leaks by a dealer.

Want to see a spring de-winterization go from a fall appointment to a photo-backed inspection and an approved estimate? Book a demo and we’ll set it up around your shop’s seasonal work.

Sources

  1. Jayco: Towable Owner’s Manual, 2026 model year (Plumbing system; Sanitizing and winterizing; Water heater; Propane; Sealants; Checklists), hosted by Heartland RVs (heartlandrvs.com)
  2. Jayco: 2025 Jayco Class C Motorhome Owner’s Manual (City water connection; Sanitizing and winterizing) (jayco.com)
  3. Suburban: Service and support FAQs (water heater operation, draining and anode rod) (suburbanrv.com)
  4. Dometic (Atwood): Water Heater Models 4, 6, 10 Operation Manual (operation, preventative maintenance, relief valve), hosted by Forest River (forestriverinc.com)
  5. Splendide: Front-Loading Washer-Dryer Winterization Instructions (No. B-2001) (splendide.com)

Written by the RVDesk team

We build RVDesk alongside a mobile RV repair business in Redding, California.

See RVDesk on your shop’s work.

Mon–Fri, 8 AM–5 PM Pacific